Pattern Testing

What is a Tester Frame

~ Michelle ~ 2 Comments

A few posts back I’d shared a recent draft. I also mentioned using a tester frame for my bra. Let me share a little about tester frames here in this post.

First Impressions

I first read about a tester frame in the Bra Makers Manual Vol. 2. I remember I made one and tried it. I also made a note in the manual. I found it hard to sew the cups into that frame, and I didn’t try it again for quite a long time.

Yes, my manuals are filled with my thoughts in the margins alongside the actual instructions.

My note may say ‘fit’, but I was meaning it’s awkward to sew the cups into the frames. However difficult I found it to sew the cups into the frame after the channeling and wire have been added, it’s still a great way to check and see, first, if your frame is going to fit. And once you have your frame, if the cups fit.

I just had an idea to take the wires out for sewing and it might make it easier to sew in the cups. I’ll have to try it.

Second Exposures

My second exposure to a tester frame was from Merckwaerdigh’s blog. This is her photo.  Margreet took us through the steps of designing a bra, and part of that was testing the cups in a frame. You can read about it here.

My Take on a Tester Frame

   For my second take on a tester frame, I had drafted my cradle, band, and cups and sewn up the bra. I knew the cradle and band would fit and they did. I didn’t expect the cups to fit, and they didn’t. They were too small. Yet I still sewed up the bra.

Let’s talk about those cups for a minute. The cups’ measurements were taken while wearing a RTW bra. That bra cups are made with stretch material. That gave me measurements that were too small because I wasn’t using  stretch material now; I was using duoplex. 

So why would I make a bra when I knew the cups wouldn’t work? Well, I knew the rest of the bra would be fine. I also knew I now had a bra that was more supportive which allowed me get new, better measurements.

Once I took my new measurements with this new bra, there was no use left for it. I could simply cut the hardware out of it, unpick all the elastics, and throw the rest away. I could donate it. Or I could use this frame for a tester frame.

Repurposing that Ill-Fitting Bra

If you have a bra that doesn’t fit the way you want it to fit, and want to make a tester frame, you have to remove the cups.

Here’s what I did.

On the bra, I measured from the seam along the bottom of the cup into the cup by a half-inch, Then I cut along that line.

See the black on the edges? That’s the 1/2-inch mark. That little bit of material sticking out is what is left of those too-small-cups that I’d cut out.

I also cut the seam where the strap joins the cup.

Now what’s left is a tester frame. It has straps, hooks and eyes, elastics, a bridge, the cradle for new cups. It has everything a bra has, except the cups.

What was left of the too-small cups I threw away. There was no use for them now.

Testing the Frame

I sewed up new cups and marked the 1/4-inch seam on those. In the photo above, you can see the bright pink line on the cups – that was going to be my seam line.

I got out some black thread and a needle and started sewing them into the frame by hand. Remember I found it hard to sew them in by machine. If you do try using your sewing machine, take the wires out, and move your needle over to the far right. Those two suggestions should make a difference. Oh, and use lots of pins!

Or sew the new cups in by hand.

I sewed the new cups in as closely as possible to the original seam in the cradle on the tester frame.It wasn’t pretty, but it was completely functional for its purpose – to see if these cups would fit. And they did.

Happy creating!

Ultimate Bra-Makers Challenge

~ Michelle ~ 10 Comments

I had it all planned out. I bought some lovely ivory duoplex and power net to make both my tester bra and my first bra once the ‘final’ draft was completed.

Then something fun happened.

The Ultimate Bra-Makers Challenge

  Beverly, from Bra-Makers Supply, announced the Ultimate Bra-Makers Challenge starting in January 2018. Have you seen it? Here’s a blurb from the BMS site:

“Our idea is simple – each month starting on January 1, we will give you a theme with a challenge to complete by the end of the month. The challenge will be to use a new fabric or a new pattern chosen from Bra-makers Supply (yes, we will discount those items!) You can submit photos of the finished project to enter the challenge. Tag us on Instagram and Facebook @bramakerssupply and use the hashtag #bramakerschallenge2018… Each monthly winner will receive a $25 gift certificate from Bra-makers Supply. How easy is that?”

January’s challenge is the Pantone color of the year: Ultra Violet. SO pretty! I just happen to have a lilac kit from my trip to Ontario two years ago. I was saving it for when I got my draft just right.

The kit is one my hubby picked out. It had the paler lace that is on top in the photo. Something I’ve learned about myself in this bra-sewing journey is I prefer tone-on-tone bras. So if I’m going for red, I want all the tones to be close to the same shade. So I wasn’t over-the-top in love with the paler lace. I dug into my stash and found this darker purple, which was really nice. Then I saw this  lilac one on the BMS website. Love. That was the lace to go with my kit.

Pattern

I’m using my self-drafted pattern for this bra. I am so happy. This fits perfectly, and I love the color!

I used Beverly’s CD Designer Bras by You to create my own Shelley-style pattern from my draft.

Here’s the side view: Even though I’m drafting the pattern so there shouldn’t be any difference between the cups and cradle, I still find I’m having a tiny bit of a length difference. A quick little gathering stitch running along the bottom of the cup, and it fits in just fine. Also, there are no wrinkles on me, but a few on Catherine.

Here’s the back of the bra.When I was taking the photos for this, I noticed I missed catching the very bottom edge of the strap elastic under the eyes. I’ll have to take that back to the machine and tack  it down.

I love the lace detail on the back.

Road Bumps Design Elements

I had fixed everything on my pattern, and had my bra cut out. The cups were sewn. The lace was sewn on the band. The band was attached to the cradle. It was time to get the elastics out of the little finding kit and sew them on the band. Then I realized I had drafted my pattern for the ‘soft’ elastics. The new elastics I had in my kit weren’t going to work for this band.

I wasn’t happy.

The bra went into a time out.

I’ll have to draft a new band and label both bands – one ‘soft elastics’ and one ‘firm elastics’. That will save any future frustrations.

The next morning I pulled out some elastics from my stash. I tried some beige elastics behind the band, and then some black.

I decided the black looked better. Those little picots were almost a shadow behind the band. To bring all the elements together, I added a black bow behind the lilac one at the front.  The Gothic arch looks wonky here, but that’s just on Catherine. I tried to get it to lay flat, but it just wouldn’t.

I’m still deciding on the strap bows. I think I like the depth the black adds to the bows. I’ve made another black bow, so sewing them on is next.

Next panties to match.

Happy creating!

A Few Alterations

~ Michelle ~ 6 Comments

My third bra draft was pretty good. In fact, it would have been wearable except I used water-soluble thread. That little fact alone would make it good for one wearing only. Well, the water-soluble thread and the fact that it was slapped together…

It fit pretty well. That’s what I’m really trying to say here.

There were only a couple of changes I still wanted to make to this. I wanted to add a bit to the underarm area for more coverage there – just a half-inch. I wanted to round the cups a touch at the apex. And I wanted to lower the bridge a half-inch as well.

Changes

While I was making those couple of changes I listed above, I decided to change the style of the bra too. I added a power bar. So  now it’s the same style as the Pin-up Girls Shelley pattern with a split lower cup and a power bar. Shelley has been my favorite pattern, so it only makes sense I make something like that. 

Making these changes were such much easier than the actual drafting of the cups. That was much more of a challenge.

 Leftovers

After soaking my bra, all the threads dissolved, and I was left with bits again. This is great as I can re-use most of these bits. It’s just the cups I need to cut fresh. I found the band too big as well, so have adjusted that. It’s all ready to go for a second sew. 

Stay tuned for my bra-drafting. I’m hoping only one more draft and I’m cutting into some gorgeous lace again.

Seize the Day

Remember how I couldn’t put a bow on Em’s Watson because she didn’t want to take it off once she’d tried it on? Well, I had my chance. The circumstances surrounding this? Well, I don’t want to know. I do know the bralette was on the floor and got stepped on… That was already more than I wanted to know.

It seems little plastic rings can’t withstand being stepped on. I had to repair the bra. I replaced the rings and sliders with metal ones from a little second-hand bra I bought. I also added the bow! I had no intention of missing that opportunity.

Happy creating!

A Third Bra Draft

~ Michelle ~ 6 Comments

My third bra draft really was a success!

A Few Differences

There were a few things I did differently this time. One of the changes I made was to use water-soluble thread – and it came in handy! I realized very quickly I had mis-measured my cradle for the elastics. A quick little soak in some water, and it was all bra bits again rather than a partially-sewn bra meaning I’d have to start over or unpick the whole thing.

 I was not expecting to have a bra when I was done. I was simply seeing how my draft fit and what changes I needed to make. That is a very freeing feeling.

My Pattern

I made a diagonally seamed bra with a split lower cup. Nothing fancy for this bra – I only want to see the fit.

My ‘Kit’

  The same attitude I had for the pattern, I had for the kit. Nothing fancy, just bits of this and bits of that. Not all the bits were even matching, but they worked for their purpose.

In this little pile of a kit, I have beige Duoplex and Power Net, some beige and some white bottom band elastic, white upper band elastic, white strap tape, and blue trim! I’m really not expecting this to look good.

As well there’s the YLI Wash-A-Way thread. If you haven’t tried it, it’s great! It works perfectly for testing a pattern like this.

A Hot Mess

Honestly, the sewing on the bra looks terrible. Well, not the sewing really. It’s more the techniques or lack there of. It’s a mis-match of colors, and I didn’t do a lot of the things I’d normally do to ‘neaten’ things up. Just look at the bottom band elastic.

 Normally, I trim the elastic under the channeling – I like a thinner band running under the cups. Not this time. This time I’ve simply folded the channeling over the elastic and pushed it out of the way.

It’s looks so bad.

 While we’re talking about the bottom band elastic, I used two colors because I didn’t have enough of one color to do the full band. I used a great technique of piecing together bits of elastic. I saw Monica Bravo do on a YouTube video. It’s quick and it really doesn’t show at all from the front. You can view the video here.

You can see I wasn’t trimming anything, not even threads. This was a quick sew to see how things were going to fit. That’s it.

Does It Fit?

I have to say I am so surprised by the outcome of this drafting experience. First off, I never thought I’d be drafting my own bra pattern from measurements!

Secondly, I made a very wearable bra! Well, it would be wearable if I hadn’t used the water-soluble thread! But it fits. There are a few tweaks I want to make, but it fits.

The whole time I was sewing this, I kept thinking how I’d never sewn/thrown a bra together like this. There are bits hanging or sticking out everywhere! The upper band elastic is hanging out of the side of the cup because I didn’t finish the straps; on the other side it’s hanging down the back at the hooks and eyes. The channeling is sticking out. It really is a mess to behold!

There’s not a top-stitch to be found, and barely a back-stitch present. I sewed it just enough to hold it together to try it on… well almost. I did pull on the strap a bit too much and pulled it off! I had a pin handy, so was able to continue in the trying-on/evaluating process. 

Adjustments

  There are only a couple of adjustments I want to make. I plan to add a little more coverage to the underarm area – probably a half-inch will do. I want to lower the bridge by about a half-inch as well. Rounding the apex and adding a power bar will complete this. I’ll also likely do another test run. Then I should have a perfectly fitting self-drafted bra and pattern. What a feeling!

Happy creating!

Testing my Drafted Pattern

~ Michelle ~ 4 Comments

I’ve made my drafted pattern, but I want to check how it will fit before I sew up a bra.

Testing

There are a couple of ways I can test the fit before I start sewing up a whole bra. In Beverly’s Craftsy class, Foam, Lace & Beyond, she shows how to convert your Classic pattern from a diagonal seam to a horizontal seam. I did this to compare the two patterns because the original pattern I made from the draft was a horizontal seam.

It’s looking pretty good on paper and I’m feeling encouraged.

Alterations

Even though I’m encouraged by my pattern, I still want to make a tester cup. There are no alterations done to this basic pattern, and I have a list I usually need: make the underarm smaller, a flat spot adjustment, check the bridge height and bottom width. Then there are the Omega considerations. Making a test cup is simply one more confirmation for me.

This tester cup is looking good too.

Here’s the dart I pinched out. I’ll adjust the pattern and then it’s time to cut out a new bra! I’m going to adjust the strap and upper cup at the side too. You can see both in the photo below.

A Trial Bra

My sewing was going along nice and smoothly, and then a tiny snag. I pulled the elastic out of the finding kit and it was the ‘old’ elastic. There’s been a change in elastics and the newer one is 20% less stretchy. It’s a good thing the Fairy Bra Mother blogs. I went over to Beverly’s blog and used her information to take out that extra width I’d added to my band. You can read her post here.

I not only looked that up, but also her post on sewing a Gothic Arch because it’s such a comfortable alteration.

New Bra

Here’s my new bra. It fits so well, and I’m so excited about it! I think I’m more excited about this bra than any bra I’ve made in the past.

Here’s the side view. You can see there are a couple of little alterations I want to make.

The pin there? I want to take a little more out from the underarm there. As well, I’ll want to raise the side there 1/4-inch. The wire is coming to the top of the elastic, that’s why I didn’t finish it there.

The back is fine. Taking out that 20% makes it fit perfectly.

Here’s the Gothic arch I added. It is such a comfortable pattern alteration.

All in all, I’m thrilled with my new bra, and the drafting experience.

Happy creating!

P.S. You may want to look at A Review of Sewing Bras: Foam, Lace & Beyond.

Patterns

~ Michelle ~ 2 Comments

After working on drafting a bra from measurements, my work wasn’t done with the draft. The next step is to use that draft and make a pattern. Let me show you a little of the progression so far.

Drafting

Here’s the draft. It doesn’t look anything like the pieces I’ve seen in bra patterns.

Horizontal Seam

Then, a few more steps and things start to look more familiar. Beverly takes you through it all in her manual. Take a look at these pieces. These actually look like bra pattern pieces.

I’m not the biggest fan of a horizontal seams. I used one when I made my Heather bra.

Common Bra Seams

Here are some different seams shown in bras (photos are from Bra-Makers Supply and Sewy):

Vertical Seam

I’ve also tried the vertical seam when I made KS 3300. Once I started making my own patterns from the draft, I had to try each pattern. This part of the process was definitely fun for me. The photo of the vertical seam is from the Sewy website. It’s their Linda bra pattern.

Diagonal Seam

My favorite seam in bra-making so far has been the diagonal seam. That’s the bottom left in the photo collage above. A diagonal seam is what we find in the Classic pattern or the Shelley pattern from Pin-Up Girls patterns.

I also love the power bar and split lower cup on the Shelley. Here are a few of my favorites from that pattern.

I love this pattern, and know I will make it using my drafted pattern!

Curved Seam

The one I really wanted to try was the curved seam. All the gorgeous Cloth Habit Harriet bras I’m seeing were making me want to buy that pattern too. I had to be very strict with myself not to buy yet another pattern I have. The photo in the first collage is from Sewy again. It’s their Isabell pattern, which I have. I also have a clone of a Fantasie bra that is a curved seam too. I didn’t need one more pattern, but I was tempted! However, I did want to make one when I was making the patterns.

Patterns I Made 

Here are all my new patterns. I just need to add seam allowances to some of them, and make little changes like adjusting for a flat spot, thinning the band under the cradle, and lowering the bridge.

I also drafted my a new cradle and band.

Happy Creating!

P.S. You may also be interested in Sewing Bras: Foam Lace & Beyond.

Here’s some exciting news.

Merckwaerdigh

The news is from Merckwaerdigh’s Etsy shop. Here’s what Margreet said in her post on Facebook: “SPRING … a perfect time for a major change! As of today all listings in the Merckwaerdigh shop at Etsy are FREE SHIPPING!!!“

She is raising her cost a bit, but what she is adding to the costs will still be lower than shipping costs! Yay!

Canada Cups Posts for Sunday, September 18th, 2016

~ Michelle

picmonkey-image-banner-2016

Here is our wrap-up post for the tour. What an incredible week it’s been! Don’t forget to enter the give-away and come back for some wonderful prizes.

Sunday, September 18

  • Linda, the instructor from the newest Corset-making class and owner of her own Corset business, is doing our wrap-up on Farthingales.

14339952_10210984887124239_819227118_o

All of the talented bloggers on this tour have done a fabulous job!

bloggers

If you’re looking for any of the past posts, here they all are.

Follow the magical tour to see what we all have under our clothes

Canada Cups Logo Draft

♥

Sunday, September 11

♥

Monday, September 12

♥

Tuesday, September 13

♥

Wednesday, September 14

♥

Thursday, September 15

♥

Friday, September 16

♥

Saturday, September 17

♥

Sunday, September 18

  • Linda, the instructor from the newest Corset-making class and owner of her own Corset business, is doing our wrap-up on Farthingales

Whoohoo! It’s giveaway day today!

♥

Monday, September 19

Have you entered the giveaways yet? Today’s your last chance.

♥

Tuesday, September 20

Giveaway winners announced on all the blogs:

Life of a Fairy Bra Mother, Little Heart Threads, Glitter in my Coffee, Michelle’s Creations, Mrs. Weaver’s Finest Unmentionables, Braphoria, Gracious Threads, Élégantine!, Shelaine’s Designs, That’s so Venice, Sprouting Jubejube, Flying by the Seam of my Pants, The Wild Stitch, Farthingales Corset Blog

♥

After September 20

  • Come back to visit all the blogs for followup posts. It’s always fun!
  • Craftsy class discounts expire at midnight Sept. 30

♥

Happy creating.

A Review of Sewing Panties Construction & Fit

~ Michelle ~ 125 Comments

Welcome to Michelle’s Creations for the Canada Cups – Cross Your Heart Relay blog tour, 2016.

banner-improvedI hope you’re enjoying all of our makes and reviews so far. This time around, I’m reviewing Beverly Johnson’s new Panty class and so is Deb, my booty buddy, from Sprouting JubeJube. Make sure after you read my post, you hop on over to read Deb’s thoughts on the class. If you started with Deb’s review, welcome here!  I do know Deb has been really busy with all her makes and has them all here in a separate write-up than her class review.

header_11223

Don’t you love Craftsy? It really is the best. They offer online classes that never expire, and in so many different categories (sewing, cooking, gardening, painting…); the instructors they get are the best and they answer your questions; Craftsy offers kits and supplies as well. They really are great!

You’ll see in my sidebar menu, I’m an affiliate with Craftsy. I decided to do this because I can do this without any compromise. I really do think they’re great. You won’t see me stand behind everything. But Craftsy, I do.

Back to Sewing Panties Construction & Fit. I started watching. I watched the class half way through the first night. Then got up the next morning and watched the rest of it. I felt ready and confident to draft my own panties which was something I’d wondered if I could really do before the class.

Beverly assures us that drafting our own panties isn’t hard. It’s just a few simple measurements. Then she proceeds to show us just how to do it. This photo is from Craftsy showing Beverly making her master panty pattern.

She was absolutely right! It’s not hard.

full_2846_373118_DraftingaMasterPattern_1

The drafting of the panty is very reminiscent of Suzy Furrer’s Sloper classes. Once we’ve drafted our pattern, Beverly moves on to show us the three basic styles of panties – Brief, Hipster, and Bikini – and how to make each one from our own master pattern.

From those three styles, Beverly shows some more variations like making your own French cut panties. There is also a style with the seams in the front. I had just been looking at the Make Bra DL21 pattern. I’d read great reviews on them and how the seams didn’t show at all. I’m going to try my hand at drafting my own!

My big question is how will my class-drafted pattern compare to my favorite pattern?

Before I made a pair up, I wanted to compare my class-drafted pattern to my favorites: Kwik Sew 2286.

Here are both back pattern pieces – the black outline is the class-drafted pattern; the white pattern piece is my 2286 pattern:

back 2

The pencil wasn’t showing up very well in the photo, so I redrew the lines in black on my computer. The class-drafted Hipster hits the center back exactly the same as my 2286s. The hip sits a bit higher on the class-drafted pair. As well, the class-drafted back is a bit wider in the hip and gives a little more cheek coverage. I had no idea my 2286s were cheeky!

I was thinking about the size difference, and remembered Beverly does suggest in the class to start with a 20% reduction when drafting the pattern. Clearly, my 2286s have more than 20% reduction, which shows even more on the front piece.

Front

Again, the front is bigger on my class-drafted pair. And the Hipster line sits a little lower. The leg opening on the front of my class-drafted pair (again, outlined in black) is definitely lower, and that would be something I’d want to change.

Gusset

The class-drafted gusset is shorter and although you can’t tell in the photo, it’s a touch narrower as well. I’d even narrowed the gusset pattern piece on my 2286s.

For my panties, I’m going to use my favorite 2286s like I often use my sloper – to help me get the fit I want. I will change the leg opening on the front, lengthen the gusset a tiny bit, and since I haven’t found my 2286s to be too small at all, I will narrow the class-drafted pattern.

It’s time for new panties! New, drafted-to-my-measurements, incorporating-all-the-aspects-of-my-favorite-pattern, and matching-my-new-bra new panties. These are not just any panties!

panties on table

Oh, I like these. I incorporated the lace application on the legs the same as my 2286s, and did a lace front panel to match my bra.

I wanted to show you a few more details. One of the things I’ve learned making my own panties is the side seam is a weak spot when you’re using lace on the front like this. So, for these panties, I used a 1/2″ strip of knit interfacing to reinforce the seam.

reinforement

As well, having a lace front isn’t quite the same without some elastic. It will often be too loose. So a little bit of lingerie elastic behind the lace is hardly visible, but makes a big difference when you’re wearing them.

Elastic behind the lace

I like everything to look as nice inside as out. I pin my lace out of the way and use my Pinking blade to trim away the excess fabric.

Pinking the edges

There’s only one more thing to add. This is one of the bows I made for my bra.

One more thing to add

Here’s my matching set.

Full set on table 2

 I love them both!

Set on Catherine 3

I loved making self-drafted panties, but that wasn’t all I made. As well as making these panties, I reviewed a pattern.

 

 Here are the panties I made:

il_570xN.1022408585_jahx

Yes, it’s the Pin-Up Girls Boy Short Collection.

Along with covering Beverly’s newest class, Deb from Sprouting JubeJube and I are both reviewing panty patterns, but not the same pattern. I’m reviewing the Pin-Up Girls Boy Short Collection. Although I know what pattern Deb is making, I’m not going to tell. You’ll have to go to Deb’s blog to see her pattern review and all her makes. She really did make some lovely panties, and we found out we love the same materials. Really. We have the same Cotton Lycra stash. That’s all I’m saying.

Let me show you the Boy Shorts I made.

Front of panty

 They look just like Boy Shorts, but they also looked bigger than what I usually wear.

comparison

And they are bigger. To be totally honest here, they looked HUGE to me!  It’s mostly the different shape. Boy shorts have material over the leg and what I usually wear doesn’t. Oh my! Here they are being compared to my favorite Kwik Sew 2286s. I know what size not to use so my next pair will fit.

The best part of these panties is the back. I made view 4. They really have a super cute back and I will use this feature in the future.

Back lace detail

Isn’t that a lovely detail?

I want to thank Bra-Makers Supply for providing me with the Pin-Up Girls Boy Short Collection, and Craftsy for providing me with the class Sewing Panties Construction & Fit.

14339952_10210984887124239_819227118_o

Tour Schedule Itinerary

Follow the magical tour to see what we all have under our clothes

Canada Cups Logo Draft

♥

Saturday, September 17

♥

bloggers

A big thank you to our wonderful bloggers. They’ve all done such a great job!

Happy creating!