Flexible Wires

Here’s a little history of my learning curve on the Omega shape.

Way back in 2012 I wrote a post called The Dawn of the Alteration Age. That was the beginning of my journey in understanding and learning about the Omega shape and the alterations needed to help fit it. In that blog I wrote:

After a few bras, I made a call to Bra-Makers Supply with a question. You see, every bra I wore, whether RTW or one I’d made, all left a line or imprint about an inch or so under the bust line. I was simply wondering what caused this.

Beverly, the owner of Bra-Makers Supply, and author of two manuals on bra-making gave me my answer: the underwires I was using were either too big or too small.

Hmm, too big or too small really wasn’t the answer I was wanting, but it did help me to realize one thing – my wires weren’t fitting. They were the same wires I’d worn in RTW bras.

So, what is the Omega shape? What is this mysterious breast shape all about? Well, I can’t say every woman with an Omega shape will be the same, but there is a common thread: the actual breast is larger than the root of the breast. If you’re wondering what that mean in terms of bra-making – it means the wire/cradle will not match the cup size. For me, I need a 36 wire/cradle, but a cup that would normally take a 42 wire/cradle.

These two sized parts don’t go together easily as they don’t match in size, so there have to be alterations to get that larger cup into that smaller cradle.

Here’s an older photo showing the different length between the two parts. The cup is on the bottom.

untitled (2)

In this photo, you can see the cup extending out past where the cradle and the wire will end.

There are a couple of alterations to help ‘ease’ that cup into the cradle. One method that I’ve used quite a bit is to run a gathering line of stitches along the lower edge of the cup where it will fit into the cradle, then gather. You’ll have to eye-ball it a bit – gather, pin it in and see if you need to adjust the gathers or not. I tend to over-gather, so usually have to let it out a bit.

untitled (3)

I find this method the fastest and easiest alteration. It does leave a few small puckers in the bottom of the cup, but seriously, who’s looking there?

untitled (6)

untitled (7)

As well, I think the puckering is a bit exaggerated on Catherine, as she’s not the same size as me. When I’m wearing the bras, I really don’t notice any puckering.

Another method of removing that excess is one I used when I first started making the alterations – I was trimming the corners of all the cup pieces to take out that inch or so of excess along the bottom of the cup. Basically making little darts all along the seams. The Shelley pattern was good for taking that excess out. But I had to be very careful – although I didn’t need the fullness at the seam line, I did all the fullness in the cup. And to be honest, it was a lot of work.

untitled (8)

The benefit is it’s a much neater looking seam line. I’ve found it’s not worth all the fussing with the seams. I’ve found just using a little steam on the bra after I’ve sewn it really makes most of the little puckers disappear.

One last thing to consider when dealing with the Omega shape is the wires. Often a Vertical wire is recommended, and many women find that the perfect wire for them.

Here’s a great photo showing two wires that are the same size – one Vertical which is much narrower, and one is a regular long wire.

untitled (10)

That’s quite a difference. As helpful as that Vertical wire is for many women dealing with an Omega shape – I needed more help. There’s a big difference between 36 and 42 wires. I needed both the narrower shape, but also the length and I wasn’t getting that with the smaller Vertical wires. I found Flexible wires were perfect for me.

untitled (4)

In the above photo you can see how much narrower that Flexible wire can be. I found the Flexible wires to be perfect for me in dealing with the Omega shape. Along with the alterations I make to the cup (to help it fit into the smaller cradle), I’ve found using the Flexible wires really made a huge difference and made my bras (finally) fit me perfectly.

Happy creating!

In my efforts to decide if I prefer the Sewy Rebecca pattern or the Pin-Up Girls Shelley pattern, I made another Rebecca. I know I love my last Shelley bra, and wanted another comparison with a few more adjustments made to the Rebecca.

This time I used a little bit of lace that was left over from a bra I’d made for a friend. And I mean there was just a little bit of lace. There was just barely enough for the upper cups – no mirroring the lace here, but they’re close – and then I had to get creative with the scraps that were left over to use them to make matching panties.

Here’s my very pretty Pink and Ivory Rebecca:

Front

This is so pretty! I love this lace and have looked for it again, but… I can’t find it anywhere. I’d bought it at Bra-Makers Supply, and I haven’t seen it since. I’m ready to start hoarding lace! This is a lovely pink lace with very distinct ivory or cream in it. And it goes so well with the ivory Duoplex and Power net.

Pretty Side

On the side view, you can see where I added just a thin strip of lace that was left over. It doesn’t take a lot of lace here to make the side look so much prettier.

Back

And a basic back. I’m still using my alternate method of attaching the straps. I use some of the bottom band elastic on the outside of the band and fold that over the top of the band with a slider attached to it. Using the elastic here allows more stretch and movement than the strap elastic, it also conforms to the U-shape more smoothly. I also use two sliders rather than a slider and ring. I find the strap has a little less movement and making it less likely for the strap to fall off my shoulder.

So, what alterations did I do to the Rebecca to make it fit me?

The first changes I made were to the bridge – I know I have to lower it 1/2″, and an adjust for a flat spot on the bridge too. I also changed the cradle to a smaller cradle that normally takes a 36 wire rather than the 42 cradle the cup needs.

I thought about making small darts in the pattern to take out the excess, and although I love that neater look, I’m finding it does compromise the cup’s fit a bit. I need the extra space those darts take away. So, I put in gathers along the wire line.

The photo below shows the excess cup compared to the cradle. I have to make that all fit.

Excess Cup

This photo shows the gathers in the wire line seam. I run a long gathering stitch along the wire line, pull the bottom thread to make small gathers all along the bottom of the cup. Then I sew the cup to the cradle. It works very well, and although there is still the odd little wrinkle where a gather is showing, steaming it well with the iron really does make most of those gathers disappear.

Gathers

I used the Flexible wires again on this bra. They do make a difference in the fit. They are long enough for me, and conform well to the shape of the smaller channeling and cradle. However, they are not the easiest to get into that narrower U-shaped cradle. I had to fight with them a little. I told myself they are worth the effort. And once they are in, I don’t need to take them out again for a long time.

The inside of the bra is so pretty with its enclosed seams. I really do love that aspect of the Rebecca pattern.

Pretty Inside