Fitting the Omega Shape

Here’s a little history of my learning curve on the Omega shape.

Way back in 2012 I wrote a post called The Dawn of the Alteration Age. That was the beginning of my journey in understanding and learning about the Omega shape and the alterations needed to help fit it. In that blog I wrote:

After a few bras, I made a call to Bra-Makers Supply with a question. You see, every bra I wore, whether RTW or one I’d made, all left a line or imprint about an inch or so under the bust line. I was simply wondering what caused this.

Beverly, the owner of Bra-Makers Supply, and author of two manuals on bra-making gave me my answer: the underwires I was using were either too big or too small.

Hmm, too big or too small really wasn’t the answer I was wanting, but it did help me to realize one thing – my wires weren’t fitting. They were the same wires I’d worn in RTW bras.

So, what is the Omega shape? What is this mysterious breast shape all about? Well, I can’t say every woman with an Omega shape will be the same, but there is a common thread: the actual breast is larger than the root of the breast. If you’re wondering what that mean in terms of bra-making – it means the wire/cradle will not match the cup size. For me, I need a 36 wire/cradle, but a cup that would normally take a 42 wire/cradle.

These two sized parts don’t go together easily as they don’t match in size, so there have to be alterations to get that larger cup into that smaller cradle.

Here’s an older photo showing the different length between the two parts. The cup is on the bottom.

untitled (2)

In this photo, you can see the cup extending out past where the cradle and the wire will end.

There are a couple of alterations to help ‘ease’ that cup into the cradle. One method that I’ve used quite a bit is to run a gathering line of stitches along the lower edge of the cup where it will fit into the cradle, then gather. You’ll have to eye-ball it a bit – gather, pin it in and see if you need to adjust the gathers or not. I tend to over-gather, so usually have to let it out a bit.

untitled (3)

I find this method the fastest and easiest alteration. It does leave a few small puckers in the bottom of the cup, but seriously, who’s looking there?

untitled (6)

untitled (7)

As well, I think the puckering is a bit exaggerated on Catherine, as she’s not the same size as me. When I’m wearing the bras, I really don’t notice any puckering.

Another method of removing that excess is one I used when I first started making the alterations – I was trimming the corners of all the cup pieces to take out that inch or so of excess along the bottom of the cup. Basically making little darts all along the seams. The Shelley pattern was good for taking that excess out. But I had to be very careful – although I didn’t need the fullness at the seam line, I did all the fullness in the cup. And to be honest, it was a lot of work.

untitled (8)

The benefit is it’s a much neater looking seam line. I’ve found it’s not worth all the fussing with the seams. I’ve found just using a little steam on the bra after I’ve sewn it really makes most of the little puckers disappear.

One last thing to consider when dealing with the Omega shape is the wires. Often a Vertical wire is recommended, and many women find that the perfect wire for them.

Here’s a great photo showing two wires that are the same size – one Vertical which is much narrower, and one is a regular long wire.

untitled (10)

That’s quite a difference. As helpful as that Vertical wire is for many women dealing with an Omega shape – I needed more help. There’s a big difference between 36 and 42 wires. I needed both the narrower shape, but also the length and I wasn’t getting that with the smaller Vertical wires. I found Flexible wires were perfect for me.

untitled (4)

In the above photo you can see how much narrower that Flexible wire can be. I found the Flexible wires to be perfect for me in dealing with the Omega shape. Along with the alterations I make to the cup (to help it fit into the smaller cradle), I’ve found using the Flexible wires really made a huge difference and made my bras (finally) fit me perfectly.

Happy creating!

Some Light Sewing and The Bra-A-Week Challenge

My hand really has to get better. I have lists of things I want to sew and do. It’s not hurting all the time now, but still sometimes – like the other morning when I tried to cut my hubby’s bagel for him. I have no idea what I did to hurt my hand, but it really does have to get better quickly.

I promised myself I’d take it more slowly this week, so I cut out a couple of pair of my TNT panties – one beige and dark purple lace, and one black and leopard mesh. When I’d originally made my beige set (pictured below), I didn’t have very much beige cotton spandex, so only made one pair of panties for my set. In the second photo, the lace on the power bar looks much lighter than the lace on the upper cup because it’s lined with beige duoplex rather than the black sheer cup lining I used on the upper cup. They’re both the same lace though.

Untitled-2

100_2972

That first pair of panties I made matched the side bar better than the front. Even so, this is one of my favorite sets, and I really found I wanted a second pair of panties to go with it. So, on this second pair of panties, I decided to more closely mirror the upper cup of the bra and use black cotton spandex behind the lace.

New-set

Below are the two pairs one on top of the other. The lace looks so different on these.

Two-pair-of-panties

Now, the black and mesh panties to give me a second pair of panties to wear with my Bra/Camisole set. That too-big pair really wasn’t going to work for me, so I used my TNT pattern again, and just re-drew the front to mix it up a bit. The bow is from the too-big pair. I’ve also un-picked the stitching from the mesh on those too-big ones. I didn’t want to waste any of it. When I showed my DH these panties, I told him they were super cute. He agreed; he thinks they’re super cute too.

mesh-panties

Now onto the Bra-A-Week Challenge! This week we’re on week 32.

Our first submission comes from Diana. Diana made a balcony bra from very lovely print.

Diana-bra-front

Diana also wanted to make something special so she made the straps herself using soft tulle and satin ribbon.

strap

Those straps are adorable! So very nice, Diana. You can read more about Diana’s bra on her blog.

Our next submission comes from Andrea.

Cream-bra2

Andrea self-drafted this bra pattern based on the method from Beverly Johnson’s Bra-maker’s Manual.

Cream-bra3

This version is a 3 piece cup with bra wadding overlaid with patterned satin. It’s lovely, Andrea. You can read more about Andrea’s bra on her blog.

Such wonderful submissions this week! Thank you and Happy creating!

Pretty In Pinks and The Bra-A-Week Challenge

This week, I’ve made another lovely Shelley bra – in pink.

Front

For this bra, I used my custom Shelley pattern, but I did make a couple of little changes.

I added some lace to the power bars, which is really only a change to the look.

power BAr

A few changes I made to the pattern itself is I made a Gothic Arch on the bridge. I didn’t get it perfect, but close. I also now know what to do for the next one. I think I missed a couple of stitches on the first pass of the elastic on the one side. When I turned it, because I missed those stitches, I got a tiny pucker. That bridge is looking so unadorned… I need to get my Hotfix crystals out and put some bling on it!

Gothic Arch

Oh, I have to show you how lovely and neat the inside is when sewing a Gothic Arch.

Inside

Do you see how the ends of the elastic are tucked nice and neatly under the channeling? Ooooh, I love that! I’m all for the inside of my bras or garments looking as nice as the outside. I lined the cups using the Sewy Rebecca method, so all my inside seams look as nice and neat as that Gothic Arch.

One other change I made was in how I put on the straps. I usually use some of the band elastic to attach the strap – making a loop at the top of the band where I put the slider.

gap

However, a few weeks ago, I showed you how that really hadn’t worked well on my beige Shelley. When I was looking at the elastics for this bra, they didn’t seem as firm as some others I’ve used, so I decided to use the strap elastic on the band. I don’t like it as much. It always seems to pucker where it meets the band when the bra is on me. It’s even puckering a little bit here on Catherine (my dress form).

One last comment on my own make. I tried the little tutorial I’d posted on making your own bows with a fork. Hmm. Well, I tried a number of times, and it did not work. I used the cardboard method again, and made little bows for my straps. I’m going to take that link out. I don’t want to recommend something that doesn’t work.

pink bow

It’s so fun to make my own bows,  I wanted to find a way to do the bows with all ribbon that actually worked and I found one. I even made a couple before I shared the site with you. You can find the tutorial here.

Now onto the Bra-A-Week Challenge! We’re on week 27!

Our first submission is from Sofia.

Sofia made a Partial-Band bra this week.

Dotted-bra

That is so pretty! Sofa made this bra from her full-band pattern and modified it. She also added an inside pocket for cookies. Sofia said this was the slipperiest Lycra she’d ever sewn. I understand about slippery Lycra. You did a beautiful job!

As well as modifying her bra pattern, Sofia made knickers from a pattern she drafted herself. They’re a high-waisted brief with princess seams.

Dotted-Bra-Knickers-set

What a beautiful set! You can read more about Sofia’s set and her alterations on her blog: Silver Lining.

Our next submission comes from David.

David made a stunning ‘open’ bra.

Zdjęcie0008

David explained with a triangle breast shape the pink lace will still cover – over the apex of the breast.

Zdjęcie0009

Zdjęcie0011

           Here we can see from the side.

Zdjęcie0010

And the back of the bra.

David is a freelance lingerie designer, his label is Bonnet Bleu.

Happy creating!

A Few Thoughts From Other Blogs

This week I want to share a few thoughts I’ve had from reading other blogs.

The first one is from Erin. Do you follow The Sewing and Life Adventures of Emerald Erin? On her June 11th post Erin made an announcement:

“A Special Summer for the Bra-A-Week Challenge!

Hi All! I said earlier this week that I would announce the summer host for the Bra-A-Week Challenge – and here is the announcement!
f8898-braaweekbutton

I am delighted to announce that the Bra-A-Week Challenge will be hosted by the lovely….

Michelle!
 
 
“Michelle is such a wonderful fellow bra-maker, and I’m sure you’ve all admired her work over the last 21 weeks like I have, and she most generously offered to host the challenge for the months of July and August for me!!”
Thanks, Erin! I’m pretty excited about hosting the challenge, and hoping some of my bra-making friends will join me and sew up a bra or two (or more) along with all the other wonderfully creative sewists who have contributed.  There’s more information on Erin’s blog if you’ve been participating in the challenge already and want to continue. You’ll still send your submissions to Erin. I’ll just be doing the write-up and posting it.
It’s great that the challenge will continue over the summer months!
This next blog comment I want to make really has nothing whatsoever to do with sewing – or does it? My good friend, Valerie over at Intricate Knits has been blogging about and telling me about her favorite author for years now. She just recently posted some scarves she designed that were inspired by Susanna Kearsley’s novel A Desperate Fortune. You can see Valerie’s designs here. After seeing the scarves, and having heard so much about Susanna, I decided I’d get A Desperate Fortune and read it myself.
This photo is from Valerie’s blog and shows a couple of the designs Susanna’s book has inspired. Valerie does such beautiful work. Check out her blog, and if you see something you love, she sells her beautiful creations on Etsy.
adesperatefortune-susanna-short-2
Aren’t these lovely?  This morning as I came into my sewing room, I didn’t even want to sew! I wanted to get back into A Desperate Fortune. So far, I have to say, I can recommend Valerie’s favorite author as well.
Happy creating!

Pattern Preferences

I’ve had a number of people ask me which I prefer, the Sewy Rebecca or the Pin-Up Girls Shelley. The Rebecca was published before the Shelley. I had also sewn the Rebecca pattern a couple of times before the Shelley pattern even came out, so was used to that pattern before I even tried the Shelley.

In fact, it was the Rebecca pattern I made for the Sew-Along hosted by Amy of Cloth Habit. It was during that time – when the Sew-Along was happening – that news of the Shelley pattern came out. I loved the Pin-Up Girls Classic pattern, and have both of Beverly’s Bra-Making Manuals, so was excited about a new pattern from her.

Over the years, I’ve had people email me and ask me which bra I prefer. And honestly, I had a hard time deciding which bra I did prefer.

The Sewy Rebecca pattern consists of a three-part cup: the upper cup, lower cup and power bar. This photo of the Rebecca pattern is taken from the Sewy website.

tzrebeccaotgr_z3

The Pin-Up Girls Shelley is a four-part cup consisting of the upper cup, split lower cup, and power bar. This photo of the Shelley pattern is from the Bra-Makers Supply website.

PB-3230%20Shelley

The two bras really are similar in design. One big difference is the Sewy Rebecca is fully lined inside the cup, and that really makes it look so professionally finished on the inside – something I love.

However, I’ve made a couple of Shelley bras now and lined them on the inside making them look as professionally finished as the Rebecca always does.

My most recent bra that I made was a Pink and Ivory Rebecca and while wearing it, I realized, for my shape I prefer… the Shelley.

So, what finally made me prefer one pattern over the other? Well,…

I have read many comments on blogs, bra-sewing forums, and personal emails to me where people have expressed their thoughts on another bra – the Marlborough by Orange Lingerie.

I know sewers who love this pattern. It’s their TNT pattern that they go to every time. I haven’t personally made up the Marlborough, so can’t say anything from personal experience. One of the reasons I haven’t made it up is I’ve heard it has a shallower fit. Another reason is I’m outside the bra’s  size range. I can play around with sister sizing and grading to get the right size for me, but hearing the bra fit more shallowly has been the one factor making me hesitate to try the bra. Although I must say, I’ve seen so many beautiful examples of the Marlborough sewn up and they all look lovely. I don’t think it’s the right pattern for me.

After wearing the Rebecca, I’ve realized there’s a shallowness to the fit of it as well. Although the two patterns, Rebecca and Shelley, are very similar, they don’t fit the same on me.

The Pin-Up Girls Shelley bra pattern gives me a nice shape and lift. The Rebecca pattern does not give me the same nice shape. Even though the patterns measure pretty much the same – the cross cup seam is the same length, and the bottom cup depth is the same, the upper cup is shallower on the Rebecca. I even added 1/4″ to it, but it still just didn’t give me the shaping I want.

Happy creating!

A Pink and Ivory Rebecca

In my efforts to decide if I prefer the Sewy Rebecca pattern or the Pin-Up Girls Shelley pattern, I made another Rebecca. I know I love my last Shelley bra, and wanted another comparison with a few more adjustments made to the Rebecca.

This time I used a little bit of lace that was left over from a bra I’d made for a friend. And I mean there was just a little bit of lace. There was just barely enough for the upper cups – no mirroring the lace here, but they’re close – and then I had to get creative with the scraps that were left over to use them to make matching panties.

Here’s my very pretty Pink and Ivory Rebecca:

Front

This is so pretty! I love this lace and have looked for it again, but… I can’t find it anywhere. I’d bought it at Bra-Makers Supply, and I haven’t seen it since. I’m ready to start hoarding lace! This is a lovely pink lace with very distinct ivory or cream in it. And it goes so well with the ivory Duoplex and Power net.

Pretty Side

On the side view, you can see where I added just a thin strip of lace that was left over. It doesn’t take a lot of lace here to make the side look so much prettier.

Back

And a basic back. I’m still using my alternate method of attaching the straps. I use some of the bottom band elastic on the outside of the band and fold that over the top of the band with a slider attached to it. Using the elastic here allows more stretch and movement than the strap elastic, it also conforms to the U-shape more smoothly. I also use two sliders rather than a slider and ring. I find the strap has a little less movement and making it less likely for the strap to fall off my shoulder.

So, what alterations did I do to the Rebecca to make it fit me?

The first changes I made were to the bridge – I know I have to lower it 1/2″, and an adjust for a flat spot on the bridge too. I also changed the cradle to a smaller cradle that normally takes a 36 wire rather than the 42 cradle the cup needs.

I thought about making small darts in the pattern to take out the excess, and although I love that neater look, I’m finding it does compromise the cup’s fit a bit. I need the extra space those darts take away. So, I put in gathers along the wire line.

The photo below shows the excess cup compared to the cradle. I have to make that all fit.

Excess Cup

This photo shows the gathers in the wire line seam. I run a long gathering stitch along the wire line, pull the bottom thread to make small gathers all along the bottom of the cup. Then I sew the cup to the cradle. It works very well, and although there is still the odd little wrinkle where a gather is showing, steaming it well with the iron really does make most of those gathers disappear.

Gathers

I used the Flexible wires again on this bra. They do make a difference in the fit. They are long enough for me, and conform well to the shape of the smaller channeling and cradle. However, they are not the easiest to get into that narrower U-shaped cradle. I had to fight with them a little. I told myself they are worth the effort. And once they are in, I don’t need to take them out again for a long time.

The inside of the bra is so pretty with its enclosed seams. I really do love that aspect of the Rebecca pattern.

Pretty Inside

And one last detail:

Clearer Crystal

I sewed a pretty crystal in the inverted V of the bridge. It has movement and does move a bit. It’s so pretty when it catches the light.

Next week some matchy matchy – matching panties.

Happy creating!

The Flexible Wire Experiment

I did a little bra-wearing experiment. I still wasn’t 100% happy with my fit. Do you get the idea I’m looking for perfection? I am!

At the end of the day, I could see when I undressed, the wires I was using weren’t fitting me perfectly. I also knew from experience that a size smaller felt like it pinched a bit. So, if the size I’m wearing is too big, and one size smaller is too small, where did that leave me?

I’d read something recently about the flexible wires available at Bravo Bella, Needle Nook Fabrics, and Sew Sassy. I decided to give them a try and see if they’d solve my wire problem. I ordered three sizes from Needle Nook Fabrics – 36, 38, and 40. Anne St. Clair was so very helpful. I must say, women like Anne and Beverly Johnson are a tremendous help to us non-professional bra-makers. Thank you!

I could tell with just a glance that the 40 wires were the same size I’d been using, so I ruled them out, initially. The 36s felt perfect but were too short for me to use. That left the 38s. I popped out the Vertical wires I’d been using from my most recent Black Butterfly bra and wore the flexible wires for a day. (Here’s a confession: I didn’t even sew the seams up!)

Here are the two 38 wires  – one regular and one flexible:

100_2951

And this second photo shows just how much these flexible wires can flex:

100_2952

That’s tremendous. There’s no way a regular wire is going to move like that! As well, the flexible wires don’t splay outward anymore than the regular wires I’d been using did – I checked. They flex inward.

Just before I popped those new wires in, I pressed them together to make the curve a little narrower. On the Bravo Bella web site, Monica Bravo has a couple of videos about the wires, and on one she explains how they can be shaped. That sounded perfect to me.

At the end of the experimental day, I could see these wires were a much better fit for me. Yay! I now have a nice little stash of flexible wires on their way to me.

Now to adjust my pattern to help with the wire fit. I’ve learned though, change one part of the bra pattern, and it means changing something else. Now I decided to look at the cradle those wires are fitting into. What I’ve been using is drawn from a 38 wire cradle that I lengthened to fit the 40 Vertical wire. I wanted to change that. Clearly, the channel that fit a 38 wire was too big.

In this photo, you can see the bridge and then the 36 and 38 cradle lines. There’s not a lot of difference between the cradle sizes, but I think one size will be just enough to make things a little more comfortable and fit better. The main problem with a cradle that’s too big is the weight of the breasts will push the bra frame down and you won’t get the support you need. The cradle really needs to fit.

I traced the 30E on this pattern (the smallest cradle size on it). I’d been using the 32E cradle for my last few bras. I’d even tried the 34E cradle, which would normally take  a 40 wire, so I would have fewer cup alterations, but I found it really didn’t help with my fitting issues – just my alteration ones.

100_2955

So, out came my pencil, eraser, and medical exam table paper. I traced of the 30E cradle and then laid my custom pattern pieces over that to add those aspects to the pattern – the narrower and lower bridge, adjusting for a flat spot, thinning out the elastic under the bust, and raising up the side 1/4″.

At this point all the alterations were good to go. In fact, you’ve seen them! I used them all on my last bra – the Sewyfied Shelley. That bra is my best-fitting bra! There are only a couple of cosmetic changes I want to make at this point. What a great feeling that is!

Happy creating!

A Pin-Up Girls Shelley with a Sewy Rebecca Twist

I’m still trying to decide which bra pattern I like better. It’s a very close match between Beverly Johnson’s Pin-Up Girls (PUG) Shelley pattern and Sewy’s Rebecca pattern. They’re quite similar – both feature a lace upper cup and a power bar. Shelley has a split lower cup as well where the Rebecca doesn’t.

Here’s the Sewy Rebecca photo from their web site. I’ve been to their site a number of times and am getting used to where things are even though I don’t speak any German. However, if you open their site in Google Translate, everything is much easier. You just can’t place an order on their site using Google Translate.

krprebecca_rosakopie_z1

Oh, that’s a lovely bra!

And here’s Beverly’s Shelley pattern from the Bra-Makers Supply web site.

Four%20piece%20cup%20Shelley%20Bra

Absolutely gorgeous!

One difference I’ve noticed is when the patterns are both flat, the upper cup along the cross cup seam is straighter on the Sewy Rebecca than the PUG Shelley. The Rebecca is on the bottom, Shelley is on top. See how much more curved the Shelley is? But they are both the exact same length.

100_2964

According to Beverly in the Bra-Makers Manuals, a straighter bottom edge on the upper cup will give more lift. Who doesn’t want more lift? However, to be honest, when I’m wearing the Rebecca, I don’t notice any difference.

So, which bra wins out? I’m still undecided. I do know one aspect of the Rebecca that does win hands down – the enclosed seams on the inside of the bra! I love that! It does take a fair amount of work, but is so worth it.

Due to my immense fondness for those enclosed seams, I Sewy-fied my Shelley this week. I added lining and followed the instructions for sewing the Rebecca to completely enclose my seams. I even upped it a bit and added a lower cup lining, so the whole inside of the cup is now lined with no seams showing. The only fault with the inside is I forgot to change thread colors and there is beige thread from top-stitching very evident on my black lining. I noticed it too late to change it.

Here’s a photo of the bra’s inside.

100_2962

Oh, those enclosed seams. That is so pretty and, I think, more professional. On one Prima Donna bra that I owned, wore, and then took apart, all the seams were enclosed. I’m still trying to figure out how they did the strap and made it enclosed too. But they did.

100_2971

Here’s my Shelley from the outside. I think I’ve figure out the best way to stuff the bras for Catherine. I use the cut and sew foam cups I made that are the same size and shape as the bra cups, AND the pre-shaped foam cups, which are sturdier. Finally, a mostly wrinkle free photo.

This is a fabric kit from Merckwaerdigh‘s Etsy shop. I really do love her laces. I’ve backed everything up here with sheer cup lining, Duoplex, Power Net, and elastics from Bra-Makers Supply.

100_2972

Here’s my Shelley from the side. Again, I added another touch from the Sewy Rebecca and used lace on the power bar. The lace here looks so different from the same lace with the black sheer lining behind it on the upper cup.

100_2961

A very basic back.

For alterations on this bra, I made a smaller cradle, narrowed and lowered the bridge, adjusted for a flat spot on the bridge and cups, made the underarm area smaller, I shortened the wire line seam (with gathers again), added linings to the cup, and used a flexible wire.

Happy creating!

Sewy Rebecca Revisited

This week I’m looking at my Sewy Rebecca pattern again. I do really like the pattern, so wanted to revisit it. However, the hard part was I felt like I was starting all over again with fitting. I’m not, but I’ve had too many ‘doesn’t quite fit properly’ experiences to not be a bit gun shy.

So, the first thing I did was compare the muslin I’d made a few months back to my correctly fitting Shelley bra. I pinned the muslin over top of the bra on Catherine.

100_2837

You can see here, the size I’d traced off and sewn up was too big. I wasn’t sure of my size, so actually graded up one size from the largest to make sure I was getting the proper depth of cup. I’m glad I did. I could see I really would be fine with one size down. Also, I traced around the muslin in pencil to show where the seam lines are underneath.

100_2839

You can see the lines here at the underarm, and in the first picture at the top and bridge. I also traced the bottom of the cup where the seam is for the cradle. That gave me a clear indication of sizing.

Once I was finished I took the muslin apart and trimmed off the seam allowance. Then I laid those pieces over the pattern pieces to compare those. Again, I was pretty sure I had the correct size. And one last comparison – I measured the wire line length and the cross-cup seam length and they both match up too. I was ready.

For the band, I laid my Shelley band over the Rebecca pattern to find the size. I really did use my whole pattern as a sloper to make the new pattern fit.

I adapted the Rebecca bridge to the right height for me, and added in the correction to the pattern for the flat spot I have. I also made the cradle smaller to fit the smaller wire I use. So the last change I need to make was to adjust the larger cup to fit into the smaller band.

Before I cut into my good material though, I sewed up another muslin.

sewy on fav

There. Almost all the wrinkles are gone. There are wrinkles on the dress form’s bra though, so this is looking perfect. Now to pick out some material.

I’ve bought some lovely material over the last couple of years that I’ve been saving for that day when I had my fit down. It was time to break some of it out!

I picked a gorgeous Black Cherry kit I’d bought from Bra-Makers Supply. I loved this kit and was really looking forward to using it. I’m not disappointed.

100_2854

One of the first things to happen was a set back. I went to press my seams and one little touch of the iron scorched my material. I don’t know how my setting dial on my iron was turned to the hottest setting, but I adjusted it and got out my seam ripper. I had some lace on that band and I still wanted to use it.

100_2863

Next I want to show you what the Omega shape means – in practical terms, it means the cup is bigger than the cradle. Do you see those edges do not meet? As this was still a bit of a test run – even though I took a lot of preliminary steps – I didn’t do any alterations to the cup pattern. I will take in the wire line of the cup’s pattern on the next one I do. On this bra I did a gathering stitch along the bottom to ease those two parts together.

100_2860

You can see here the gathers inside the cradle. But with some serious steam after the cup was sewn into the band, you can’t see the gathers at all.

100_2866

And here’s my Sewy Rebecca. I love this color. I love so many things about this pattern. It looks as neat (almost) on the inside as it does on the outside. I really love that. As I was sewing, that was what excited me the most.

100_2858

Here’s the cup before it was sewn into the cradle. All the seams are enclosed. The cross cup seam is enclosed between the lace and the lining. The power bar seam is enclosed between the duoplex and the lining. It looks so very neat inside. I’m quite excited about that.

100_2868

Here’s the bra from the side. That little piece of lace was unpicked from the scorched section I showed you earlier. I’m really pleased I took the time to do that. I’m loving that little detail. As well, the steam really did make those gathers disappear. You can’t see them.

100_2869

And here’s the back. The findings kit isn’t available in Black Cherry, so I used black. The cotton isn’t available in the Black Cherry either, so next week black cotton and lace panties to match.

Happy creating!

A Beige Shelley Set

I’m pretty sure I’ve used that title before, and will likely use it again. I really like my basics and I like the Shelley pattern by Bra-Makers Supply. Here’s my most recent Shelley:

100_2808

I need to make some proper-fitting foam inserts for photos. I don’t like all the wrinkles! However, as a bra, this is my best yet. I love it. It’s kind of funny because I saw this lace on the Bra-Makers Supply (BMS) web site, and ordered it right away. When I got it, I was putting it with my other laces, and lo and behold, there was another order I’d placed before for the same lace. Yup. I know I like it when I do that. It wasn’t the first time, and I doubt it’ll be the last. I did that with a Merckwaerdigh lace as well.  It’s good to know I really like it.

For this Shelley, I did what I did for the last couple of bras I made. Rather than making alterations to the cup to make the larger cup fit into the smaller cradle (Omega shape), I went in-between the sizes. The cup corresponds to a 42 wire, the cradle I need is a 38. I used the 40 cradle. The wire still fits. In fact, BMS say with their patterns you can go up or down a wire size if you need. That makes it perfect for me. The fewer alterations, the better because one alteration leads to another and another.

I thinned the area under the cup even though I used the larger elastic. You can see that here:

100_2813

Beverly, The Fairy Bra Mother, did a very informative blog on how to do this and I’ve been doing it since. You can read her wonderful instructions here.

I also lowered the bridge, adjusted for a flat spot I have and added a vertical dart to the pattern to take out a little excess under the arm.

It’s so wonderful to have learned to do this, and from now on I can have perfectly fitting bras. That is tremendous!

Another sparkly idea that came from Beverly was to add some Swarovski crystals to the bra. Pure brilliance. So, I added a little bling to the bra too. This bra has bows and crystals.

100_2811

I attached these sparkling little delights on the bridge just above a ‘floating’ piece of lace. I say it’s floating because I only sewed the sides of it into the seams of the cup and cradle. I used the Swarovski Hotfix Crystal Tool to attach the crystals and love the result. The only change I’d make here is one that will make it a bit easier for me – attach the crystals before inserting the under wires. However, as much as the tool seemed to want to wobble a bit, the end result looks nice and straight.

The back is quite basic.

100_2812

There is a small pucker where the hooks and eyes meet the band, but it’s not the very large wrinkle showing in the photo. That was just me not catching that the band wasn’t on Catherine (my dress form) perfectly straight. I was fighting a cold and forgot to check to see if the band fit properly into the hooks and eyes. I think there’s a 1/16″ little tuck there because I  didn’t want any edges sticking out.

Now, for matching panties.

You’d never have known it by following my blog, but I do love matching bra and panty sets. For a long time I was on a quest to find cotton because I love my cotton panties. Once I found my source at BMS, I was working on getting my bra fit down. All the materials for my bras and panties come from BMS except the elastic lace I used on the waist bands – that came from Frog Feathers on Etsy.

Here’s the first pair of panties I did:

100_2818

I love these. Nice soft cotton and matching pretty lace. Who could ask for more? I used my favorite Kwik Sew 2286 pattern and altered it. I did go up a size because the cotton just didn’t have the same stretch as some other knits I’d used in the past. The alteration I made was a simple one. Rather than cutting the front on the fold, I traced the whole front out and then cut off the one side of the front. I added a seam allowance to both sides creating two new pattern parts.

I did run into a bit of a snag not having thought it all through enough. When I was adding the lace to the waist band, I realized I didn’t want to cut off the scalloped part at the top of the lace. So I just ended the elastic lace where the other lace started. Next time I will add the elastic lace to the band before sewing these two parts together.

100_2820

Having that little blip happen helped me with my second set of panties though. Here’s my second pair:

100_2817

Yup. I love these too. It’s the same base pattern, but on this one I traced the front out and laid my lace over it. I wanted the scalloped edge at the top. So with the lace on top of the pattern, I drew a line where the lace ended. Then I traced that part again and added a seam allowance. For this set, I added the back waist elastic first. That wasn’t going to work for the font though. For the front I added a bit of left over upper band elastic. It’s hidden behind the top of the scallops.

100_2821

Here it is from the inside. I didn’t want to leave the front without any elastic, even though the lace is a stretch lace.

100_2819

Here they are, my two new matching panties.

Happy creating!